What is this? A compact, self watering planter. With a variation of the types of attachments that can go on the planter you can customize your ModMound for a wide array of plants!
How does it work? Using cotton wicks the water will follow its capillary action from the center water base to all your plants!
What plants work best? This is ideal for herbs, climbing plants, succulents, cactus, micro greens, and proplifting!
For any further questions contact support@modmound.com
Base
Petal (Small)
Petal (Large)
Accessory
Kit
16 fl oz
16 fl oz Base
Designed to hold the amount of water from a standard water bottle. This Base roughly has an 11cm height and 11cm diameter.
Recommendations:
- Print the bottom flat against the bed of printer.
- Steepest point is 45° and should be printable without support.
- Hot End Temp: 200°C - 210°C
- Bed Temp: 55°C - 60°C
- Triangle infill at 25% density
Post Processing:
- The interior of this part will need to be sanded
- The interior will then need a epoxy/urethane/sealant coating
- This is necessary to make the part watertight
x1 Length
x2 Length
x3 Length
x1 Length Petal (Small)
Made for small plants with shallow root systems. Spans the height of one layer with quick and easy attach/detach as well as redundant supports for plant security.
Recommendations:
- Print the bottom flat against the bed of printer.
- Use conical supports at ~20% density
- Hot End Temp: 200°C - 210°C
- Bed Temp: 55°C - 60°C
- Triangle infill at 25% density
Post Processing:
- Supports need to be removed and possibly sanded
- The interior of this part will need to be sanded
- The interior will then need a epoxy/urethane/sealant coating
- This is necessary to make the part watertight
x2 Length Petal (Small)
Made for small plants with medium root systems. Spans the height of two layers with quick and easy attach/detach as well as redundant supports for plant security.
Recommendations:
- Print the bottom flat against the bed of printer.
- Use conical supports at ~20% density
- Hot End Temp: 200°C - 210°C
- Bed Temp: 55°C - 60°C
- Triangle infill at 25% density
Post Processing:
- Supports need to be removed and possibly sanded
- The interior of this part will need to be sanded
- The interior will then need a epoxy/urethane/sealant coating
- This is necessary to make the part watertight
x3 Length Petal (Small)
Made for small plants with deep root systems. Spans the height of three layers with quick and easy attach/detach as well as redundant supports for plant security.
Recommendations:
- Print the bottom flat against the bed of printer.
- Use conical supports at ~20% density
- Hot End Temp: 200°C - 210°C
- Bed Temp: 55°C - 60°C
- Triangle infill at 25% density
Post Processing:
- Supports need to be removed and possibly sanded
- The interior of this part will need to be sanded
- The interior will then need a epoxy/urethane/sealant coating
- This is necessary to make the part watertight
x1 Length
x2 Length
x3 Length
x1 Length Petal (Large)
Made for medium plants with shallow root systems. Spans the height of one layer with quick and easy attach/detach as well as redundant supports for plant security.
Recommendations:
- Print the bottom flat against the bed of printer.
- Use conical supports at ~20% density
- Hot End Temp: 200°C - 210°C
- Bed Temp: 55°C - 60°C
- Triangle infill at 25% density
Post Processing:
- Supports need to be removed and possibly sanded
- The interior of this part will need to be sanded
- The interior will then need a epoxy/urethane/sealant coating
- This is necessary to make the part watertight
x2 Length Petal (Large)
Made for medium plants with medium root systems. Spans the height of two layers with quick and easy attach/detach as well as redundant supports for plant security.
Recommendations:
- Print the bottom flat against the bed of printer.
- Use conical supports at ~20% density
- Hot End Temp: 200°C - 210°C
- Bed Temp: 55°C - 60°C
- Triangle infill at 25% density
Post Processing:
- Supports need to be removed and possibly sanded
- The interior of this part will need to be sanded
- The interior will then need a epoxy/urethane/sealant coating
- This is necessary to make the part watertight
x3 Length Petal (Large)
Made for medium plants with deep root systems. Spans the height of three layers with quick and easy attach/detach as well as redundant supports for plant security.
Recommendations:
- Print the bottom flat against the bed of printer.
- Use conical supports at ~20% density
- Hot End Temp: 200°C - 210°C
- Bed Temp: 55°C - 60°C
- Triangle infill at 25% density
Post Processing:
- Supports need to be removed and possibly sanded
- The interior of this part will need to be sanded
- The interior will then need a epoxy/urethane/sealant coating
- This is necessary to make the part watertight
Water Wick
Water Wick Accessory
Not a printed part! This is the cotton strand, braided rope cord that acts as a wick for the plants to get water.
Basic
Advanced
Basic Kit
This kit includes the Base and four x3 Large Petals.
Recommendations:
- View individual part recommendations
Post Processing:
- View individual part post processing
Advanced Kit
This kit includes the Base, one x1 Small Petal, one x2 Small Petal, one x3 Small Petal, one x1 Large Petal, one x2 Large Petal, one x3 Large Petal. This includes all possible parts!
Recommendations:
- View individual part recommendations
Post Processing:
- View individual part post processing